[ Back ]   [ More News ]   [ Home ]
Mentor Graphics Outlines IC Implementation Strategy to Address Sub-45nm Challenges

ANAHEIM, Calif.—(BUSINESS WIRE)—June 9, 2008— Mentor Graphics Corporation (NASDAQ:MENT) today laid out its integrated circuit (IC) implementation strategy to help customers with the challenges they face as they move to smaller process nodes. A first step in this strategy was the merging of several offerings into a single Design-to-Silicon division: the Calibre® physical verification and Design-for-Manufacturing (DFM) platform, the Olympus-SoC place-and-route system (from last years Sierra Design Automation acquisition), and the Mentor Design-for-Test and Yield Learning solution. The recently acquired assets of the Ponte Solutions organization and NXP Semiconductors Germany DFT technology further augment the resources of the division. With this new alignment Mentor has begun to drive the integration of its three industry-leading platforms based on a common vision for delivering first-pass silicon success.

We are aligned with customers in our vision of how to meet future challenges, and have a strong technology roadmap to deliver new capabilities through platform advancements and cross-platform integration, said Joseph Sawicki, vice president and general manager, Design to Silicon Division, Mentor Graphics. Were engaged with our customers on a day-to-day basis in their design labs and fabs to ensure the Mentor offerings truly resolve customer needs at each step.

We have collaborated with Mentor Graphics for many years to address IC implementation challenges at each successive technology node, said Philippe Magarshack, STMicroelectronics Technology R&D Group Vice President and Central CAD and Design Solutions General Manager. We were also working with Sierra Design Automation before the acquisition by Mentor, and we encouraged the integration of Olympus-SOC and Calibre technologies to address the increasing challenges we foresee at 32/22nm. We believe the Mentor solution will help us meet critical IC implementation challenges such as the complexity of multi-mode, low power designs, designing for high manufacturing yields, and achieving market-leading performance.

New platform capabilities discussed at the Design Automation Conference being held this week include:

Mentor also outlined plans for integration across their three major IC implementation platforms. The success of the Olympus-SoC/Calibre LFD (Litho-Friendly Design) solution for avoidance of litho hotspots during routing will be extended with further integration of Calibre models early in the floorplanning and routing process. Concurrent Multi-Corner Multi-Mode optimization with silicon-proven Calibre DFM models will enable the Olympus-SoC product to create DFM-optimized designs in a single pass, significantly reducing the time required to reach tapeout, while at the same time allowing designers to immediately see the impact on manufacturability, timing, power, signal integrity and other chip performance factors.

DFT integration with physical analysis currently provides targeted test generation for specific DFM hotspots using the TestKompress® ATPG solution. Likewise, integration between physical analysis and the YieldAssist product allows direct viewing of suspect defect locations for reduced failure analysis turnaround time. Going forward, further integration will help customers to rapidly find the root causes of manufacturing defects by being able to quickly identify hidden systematic yield limiters by analyzing volume production test data with new software techniques. Designers can also use the results of yield learning to re-prioritize and tune their recommended design rules throughout the lifecycle of a product offering.

About Mentor Graphics

Mentor Graphics Corporation (NASDAQ:MENT) is a world leader in electronic hardware and software design solutions, providing products, consulting services and award-winning support for the worlds most successful electronics and semiconductor companies. Established in 1981, the company reported revenues over the last 12 months of over $850 million and employs approximately 4,200 people worldwide. Corporate headquarters are located at 8005 S.W. Boeckman Road, Wilsonville, Oregon 97070-7777. World Wide Web site: http://www.mentor.com/.

(Mentor Graphics, Calibre and TestKompress are registered trademarks, and Olympus-SoC, LFD and YieldAssist are trademarks of Mentor Graphics Corporation. All other company or product names are the registered trademarks or trademarks of their respective owners.)



Contact:

Mentor Graphics
Gene Forte, 503-685-1193
Email Contact
Sonia Harrison, 503-685-1165
Email Contact